Bulldog Security 1402 Guia de Instalação descarregar pdf

CONTENTS

KEYLESS ENTRY AND ALARM SYSTEM • MODEL 1402

INSTALLATION GUIDE

•

OWNER’S GUIDE

Technical Assistance

All tech personnel are expertly qualified to answer any technical questions.

Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.

Address

288 Canton Avenue • Wintersville, Ohio 43953

Telephone

Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

System Features ....................................... 1

System Components ..................................... 1

Required Tools ........................................ 1

Technical Assistance .................................. 2

Before You Begin ...................................... 2

Precautions........................................... 2

Testing Your Wires .................................... 2

Making Connections .................................. 3-4

Locating & Making Connections........................ 4-7

Neutral Safety Switch ................................. 7

Connecting Wire Harness ............................... 8

Operator Programming Instructions................... 9-12

Using Your Remote Transmitter ...................... 12-13

1 2 3 4 5 6 ... 13 14

Resumo do Conteúdo

Página 1 - OWNER’S GUIDE

CONTENTSKEYLESS ENTRY AND ALARM SYSTEM • MODEL 1402INSTALLATION GUIDE•OWNER’S GUIDETechnical AssistanceAll tech personnel are expertly qualified to an

Página 2 - SYSTEM FEATURES

OPERATOR PROGRAMMING INSTRUCTIONSENTERING PROGRAMMING MODEMake sure your vehicle is not running and the brake is pressed. The brake is to remain press

Página 3 - TESTING YOUR WIRES

10A.Turn the ignition switch to the on or run position.B.Press and hold button #1 on the transmitter for approximately 10 seconds or until parking lig

Página 4 - MAKING WIRING CONNECTIONS

11PROGRAMMING TABLESTO ENTER OPERATING PROGRAMMING MODEA. Turn the ignition switch to the on or run position.B.Press and hold transmitter button #1 fo

Página 5 - Electrical Tape

HOW TO USE YOUR REMOTE TRANSMITTER122 3.5 sec. Door Lock Pulse Length2 1 Negative Input Activated2 Negative Input Deactivated3 1 Siren Tone Output 2 C

Página 6

13This feature is useful when having your vehicle valet parked, washed or serviced. While in valet mode,keyless entry and instant panic will still wor

Página 7 - CRANKING

SYSTEM FEATURESSYSTEM COMPONENTS12 Four-Button Extended Control your car from an extended distance.Range Remote ControlKeyless Entry Remotely locks an

Página 8

TECHNICAL ASSISTANCEShould you need help. First check our website at www.bulldogsecurity.com/wires.htm or call our toll-freeTech Support Hotline Monda

Página 9 - CONNECTING WIRING HARNESS

MAKING WIRING CONNECTIONS4. Insert the wire from the unit through the hole as shown.6. Use electrical tape to wrap. Be sure to cover the wire about tw

Página 10 - PROGRAMMING OPTIONS FOR ALARM

4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection.Secure with wire ties as shown.3. Lay upper twisted pair

Página 11

5CONNECTING THE POWER AND GROUND1. Connect the RED wire from the harness to a constant 12 volt supply or to the wire you ran fromthe positive battery

Página 12 - PROGRAMMING TABLES

6Connect the control module ORANGE wire negative (-) out when armed to the optional starter disablerelay (-) negative input. Pin 86 on SPDT 30 amp rel

Página 13 - ALARM FUNCTIONS

7 the system.•To prevent water damage, the siren should NOT be mounted in a wheel well, directly behind the radiator grill or close to the ground.•Mou

Página 14

8RED (+) 12 Volt ConstantBLACK Chassis GroundBROWN (+) Parking Light OutputORANGE* (-) Output when armed; starter disable, etc.YELLOW (+) 12 Volt Igni